|
All
casework to be factory shipped fully assembled. Counter
tops for base cabinets are shipped separately for mounting at the
jobsite.
All exposed edges of cabinets to be self edged in
matching 1mm PVC edgeband, including all edges of doors and drawer
fronts.
Cabinet Base to have recessed toe space.
1.
Standards
| |
Basis
of requirement shall be
SSI Casework,
as manufactured by S&S Craftsmen, Inc.,
1307 2nd Ave., Tampa,
Florida
33605. |
2.
General Conditions
| |
All provisions
of the General Conditions of the complete set of
specifications shall be considered part of this section. |
3.
Work Included
| |
This section of the
specifications shall include all materials, hardware and labor for
fabrication of factory built melamine, plastic laminate, or wood
veneer casework. |
4.
Work Not Included
| |
All plumbing,
electrical, HVAC and fixtures related to specified casework to be
provided by others.
Unless required by the details and
specifications regarding casework, the manufacturer shall not:
|
|
|
|
A. |
Prepare
for any electrical, telephone, mechanical or plumbing
equipment; |
|
|
B. |
Furnish
common wall blocking for the support of wall mounted
casework; |
|
|
C. |
Supply
any vinyl or other base finish material; |
|
|
D. |
Furnish
dust panels; |
5.
Drawings And Samples
| |
Shop drawings
to be provided by factory upon receipt of order for architectural
approval prior to fabrication. Architect and contractor to review
shop drawings for conformance with design intent.
Changes, modifications, and alternates to be approved during
shop drawing review.
|
6.
Construction
| |
Details shall conform
to the flush overlay cabinet construction design as indicated in the
SSI Casework
catalog. |
7.
Materials
|
A. |
Finishes |
| |
- All exposed exterior surfaces of
cabinets including exterior surfaces of drawer fronts and
doors to be wear resistant melamine, 1/32" vertical grade high
pressure laminate or wood veneer.
All unexposed exterior surfaces to be faced with a
balancing sheet.
Cabinet
interiors and inside faces of doors and drawer fronts to
be surfaced with wear resistant white or black melamine surfacing or white or
black cabinet liner
balancing sheet, as required.
All counter tops to be laminated with 1/16"
horizontal surface grade high pressure laminate
and to be self edged. Cabinet backs to be
surfaced with
wear resistant white or black melamine.
|
| B. |
Particle Board |
|
|
- All particleboard to be 3/4" thick, 45
lbs. per cubic foot density. All shelves exceeding 32"
spans without intermediate supports are to be made of
minimum 1" thick particle board.
|
8.
Hardware
|
A. |
Hinges |
| |
- Flush overlay; heavy duty, all metal,
concealed type, fully adjustable, self closing.
|
| |
- Three hinges per door over 36" high,
two per door under 36" high.
|
|
B. |
Drawer and Door Pulls |
| |
- Brushed aluminum wire pull, (US 28 Finish),
5/16" diameter, 3 1/2"
c.c.,
3
13/16" overall.
|
| |
- Pulls to be through-bolted from backside.
|
|
C. |
Drawer Slides
–
Grass Zargen integrated drawer system |
|
- White Epoxy Coated, self closing with Silent
Glide rollers for smooth quiet ride.
Integrated drawer slide and side panel.
Built-in stop keeps drawer front from impacting face of
cabinet. 3-D adjustment feature allows adjustment of
drawer front in three directions. Double stop feature
prevents the drawer from falling out while being extended
and allows the drawer to be locked in the open position.
100 lb. load rating.
|
|
D. |
Hardware for Adjustable Shelves |
| |
- Line bored holes at 32mm vertical spacing
with metal pin supports.
|
|
E. |
Hanger Rods |
| |
- 1" diameter, nickel plated, steel
tubing.
|
9.
Casework Component Specifications
| A. |
Cabinet Top |
| |
-
3/4" wear resistant melamine finished
particleboard in white or black meeting NEMA standards.
|
| |
- Exposed top surfaces of units up to 84" high to
have same finish as adjacent exposed surfaces.
|
| B. |
Cabinet Bottom |
|
|
- 3/4" wear resistant
melamine finished particleboard in white or black meeting
NEMA
standards.
|
| C. |
Cabinet Ends |
| |
- 3/4" wear resistant melamine finished particleboard in
white or black meeting NEMA standards.
Exposed end surfaces of units to have same finish
as adjacent exposed surfaces.
|
| D. |
Cabinet Back |
| |
- 1/2" wear resistant melamine finished
particleboard in white or black meeting NEMA standards.
|
| |
- When finished backs are specified, exterior
surfaces to have same finish as adjacent exposed surfaces.
|
|
E. |
Cabinet Shelves |
| |
-
3/4" wear resistant melamine finished particleboard in white or
black meeting NEMA standards.
|
| |
- Shelves exceeding 32” long shall be minimum
1” thick stock.
|
|
F. |
Exposed Cabinet Interiors |
| |
Where casework is shown as open, without doors,
the exposed interior surfaces of the case shall be
considered an exposed surface and all exposed surfaces will
be finished same as adjacent exterior surfaces.
|
| G. |
Cabinet Bases |
| |
- 3/4" plywood, 4” high with 2” recessed
toe space from front edge of case.
|
| |
- Visible exterior sides to be left unfinished for
base finish material by others.
|
| |
- 1” Recess at exposed ends.
|
| |
- Bases to be shipped separately in maximum of 8
foot assembled sections.
|
| H. |
Cabinet Edges |
| |
- All exposed panel stock edges to be self edged
with matching PVC edgeband.
|
| |
- All front edges of case body and door edges to be edged with
matching 1mm PVC edgeband as indicated on the drawing.
|
| I. |
Cabinets Doors |
| |
- Doors to be 3/4" thick particleboard.
|
| |
- Exterior surfaces of doors to be wear resistant melamine,
1/32” high pressure laminate, or wood veneer.
|
| |
-
Interior surface to be laminated with wear resistant
melamine
or
white or
black cabinet liner balancing sheet.
|
| |
- Edges to be self edged with matching 1mm PVC
edgeband.
|
| |
- Edges to be edgebanded last.
|
| J. |
Drawer Body |
| |
- Drawer bottoms and back to be ¾” wear
resistant melamine.
|
| |
- Drawer sides are part of the Grass integrated Zargen
drawer system.
|
| K. |
Drawer Front |
| |
- Fronts to be 3/4" thick particle board.
|
| |
- Exterior surface of front to be melamine,
laminated with 1/32” high pressure plastic laminate or
wood veneer.
|
| |
-
Interior surface to be laminated with
wear resistant
melamine
or
white or
black cabinet liner balancing sheet.
|
|
|
-
Edges to be self edged with matching 1mm PVC edgeband.
|
| L. |
Counter Tops |
| |
- All counter tops for base cabinets to be 1 1/2" thick.
|
| |
- Top surface to be laminated with 1/16" thick horizontal grade high pressure plastic laminate.
|
| |
- Underside of top to be
laminated with a balancing sheet.
|
| |
-
Back splashes and end splashes
to
be 4” high (sent loose), laminated with 1/16” high
pressure plastic laminate on exposed surfaces and
laminated with a balancing sheet on concealed surfaces.
|
| |
- All tops to be edged with high pressure plastic laminate.
|
| |
- Sink cut-outs provided when specified.
|
|
.gif){kind=spacer}
